MD6420C

Request a Quote

Vertical Tabs

Specifications

OVERVIEW

Specifications

Hole Diameter

Up to 311 mm (Up to 12.25 in)

Engine

C32 ACERT

Bit Load

Up to 41 346 kg (Up to 91,152 lb)

Operating Environment

Minimum ambient rating (standard)

-1 ° C

Maximum ambient rating (standard)

52 ° C

Altitude

Up to 4572 m (Up to 15,000 ft)

Note

Optional cold weather packages available

Pull-down/Hoisting Capacity

Retract rate

0-33.5 m/min (0-110 ft/min)

Pull-down capacity

Up to 383 kN (Up to 86,000 lbf)

Hoist capacity

Up to 311 kN (Up to 70,000 lbf)

Drilling feed rate

0-33.5 m/min (0-110 ft/min)

Head travel (16 m/50 ft mast)

18.29 m

Head travel (13 m/40 ft mast)

15.24 m

Head travel (10 m/35 ft mast)

12.19 m

Cable type – 29 mm (1.125 in)

DYFORM 8

Bit load force

Up to 41 346 kg (Up to 91,152 lb)

Rotary Drive System

Torque, dual motors

0-17 313 N∙m (0-12,769 lbf-ft)

Rotation speed

0-137 rpm

Operator’s Cab

Type

Shock-mounted; two-man, integrated FOPS certified

Floor area

4.85 m2

Height inside

2146 mm

Windows (tinted safety glass laminated in rubber mounting)

14 mm

Number of windows

Number of doors

Two (2) with windows (included in above)

Climate control

Roof-mounted, AC/heating/pressurizing unit

Other

Window wipers and washers

Location

To the right from the mast if facing rear deck from the rear end

Undercarriage

Maximum drive horsepower per track

216 kW

Brakes

Spring set, hydraulic release

Tram speed maximum

2.27 km/h

Number of rollers on each side

Total of 16: (13) lower rollers, (3) upper/carrier rollers

Brake release

Automatic

Front

Three-point oscillating type

Track adjustment means

Hydraulic with grease gun

Track drive disconnect

Standard (manual)

Rock guards/chain guards

Standard full-length guards

Gradeability mast down – CDH (cab down hill)

25%

Gradeability mast down – CUH (cab up hill)

13%

Drill Table and Work Deck

Table height off ground

1448 mm

Components

Pipe loading guide roller

Components

Stationary rear deck

Components

Left rear swing gated handrail (dual gate design)

Components

Rear deck bit storage box with aluminum cover

Components

Hydraulically operated viewing hatch with LED hatch viewing spot light

Leveling Jacks

Number

Lift capacity – each

511 kN

Pad diameter – Non-drill end

762 mm

Pad diameter – Drill end

914 mm

Stroke on non-drill end

152 cm

Stroke on drill end

122 cm

Accessories, Tools and Handling Equipment

Top Adapter Sub

Bottom thread – depends on pipe diameter

Bit Sub (Rotary Application)

Top thread – depends on pipe diameter

Bit Sub (Rotary Application)

Bottom thread – API reg. 168 mm (6.625 in)

Top Adapter Sub

Top thread – API reg. 140 mm (5.5 in)

Top Adapter Sub

Diameter depends on pipe diameter

Shock Sub (DTH Application)

Thread – API reg. 140 mm (5.5 in)

Bit Sub (Rotary Application)

Table bushing roller-type or two-piece with replaceable liner

Pipe Rack (Inside the Mast)

Carousel with stationary pods and breaker plates

16 m Configuration

7.62 m (25 ft) × 2 as starter and four pieces of 7.62 m (25 ft) in carousel

16 m Configuration

Outside diameter – 194 mm (75⁄8 in) or 219 mm (85⁄8 in)

13 m Configuration

12.19 m (40 ft) starter and five pieces of 12.19 m (40 ft) in carousel

13 m Configuration

Outside diameter – 194 mm (75⁄8 in) or 219 mm (85⁄8 in)

10 m Configuration

10.66 m (35 ft) starter and five pieces of 10.66 m (35 ft) in carousel

10 m Configuration

Outside diameter – 194 mm (75⁄8 in) or 219 mm (85⁄8 in)

10 m Configuration

Length of drill – 10.67 m (35 ft)

Winch System

Rating – 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Winch System

Cable size – 13 mm (0.5 in)

Pipe Handling

Sliding deck wrench

Pipe Handling

Fixed cable pipe catcher or optional hydraulic safety arm/pipe catcher with drill function interlock, when pipe catcher is not closed

Pipe Handling

Manually removable or optional hydraulically operated bit basket

Pipe Handling

Lifting bail-drill pipe/bit sub

Compressor (Standard): Poppit inlet, fixed displacement

Discharge air flow (sea level)

56.6 m3/min

Maximum operating pressure

6.9 bar

Compressor (Optional): Type 1 – Butterfly inlet, adjustable from half to full displacement

Discharge air flow (sea level)

73.56 m3/min

Maximum operating pressure

6.9 bar

10-, 13- or 16-Meter Mast Configuration

Hole diameter

Up to 311 mm (Up to 12.25 in)

16 m/50 ft mast – Depth single pass

16.46 m

16 m/50 ft mast – Multi-pass

Up to 46.9 m (Up to 154 ft)

13 m/40 ft mast – Depth single pass

13.4 m

13 m/40 ft mast – Multi-pass

Up to 74.4 m (Up to 244 ft)

10 m/35 ft mast – Depth single pass

10.29 m

10 m/35 ft mast – Multi-pass

Up to 63.4 m (Up to 208 ft)

Angle drilling

30° (in 5° increments)

Compressor (Optional): Type 2 – Poppit inlet, fixed displacement

Discharge air flow (sea level)

42.5 m3/min

Maximum operating pressure

10.3/24.1/34.4 bar (150/350/500 psi)

Hi/low pressure switch, bit oil injection system

114 L

Mainframe, Decks and Walkways

Jacks, mast pivot and deck

Welded integrally to mainframe

Machine deck

Access both sides

Engine – C32 ACERT* (Standard)

Model

C32 ACERT

Rated horsepower

680 kW

Fuel tank

1514 L plus, 1703 L (400 gal plus, 450 gal)

Emissions

* The C32 ACERT engine meets U.S. EPA Tier 2/EU Stage II equivalent emission standards

Engine – C32 ACERT* (Optional)

Model

C32 ACERT

Rated horsepower

775 kW

Fuel tank

1514 L plus, 1703 L (400 gal plus, 450 gal)

Emissions

* The C32 ACERT engine meets Tier 2/Stage II equivalent emission standards

Controls

Manuals

Operations/maintenance manuals and all schematics are stored in drill monitor

Display

English control system display text ex-factory. May be changed to other languages by dealer.

Components

Basic engine shut down timer

Components

Drill performance and monitoring/diagnostics system

Components

Electronic compressor control

Electronic control:

– Monitoring – Diagnostic system

Components

Filter indicators

Components

High/low tram speed select (high only when mast is down) interlock

Components

HMI touch screen control

Components

Mast lock indicator

Components

ECM (Electronic Control Module) provides fast and reliable control of all drill functions

Components

Pump drive gearbox temperature sensor

Components

Rotary head RPM gauge – digital

Components

Tram interlock, machine outside stability limits

Components

Tram interlock, pipe in hole

Components

Tram interlock, mast up and locked or down and parked

Components

Jack/tram interlock

Components

Cab environment control (AC, filter indicator, heat, fan speeds)

Components

Pipe positioner sensor

Components

Drill depth meter

Components

Drill function interlock, mast up and locked

Components

Rotary torque control

Components

Head clear interlock, rotary drive clear of carousel

Components

Winch interlock

Components

Jack pressure sensor

Components

Virtual rotary head travel stop

Components

Wiring for terrain interface provided

Base Machine

Components

Fuel tanks isolation valves

Components

Hydraulic tank with isolation valves and interlocks

Components

Slip resistant decks and walkways

Components

3217 L (850 gal) fuel, (two tanks mounted under engine/compressor) with manual and remote fill

Components

Bolt-on hand rails with kick plates

Components

Cat® maintenance free batteries

Components

Stainless battery box, sliding drawer type

Components

Remote jump start terminals

Components

Tow hooks (front end)

Components

Lift lugs (for base machine minus mast)

Components

Walkways around the drill, 360 degrees

Components

Swing up steps, access/egress

Components

Self-closing gates

Components

Two stage mast raise cylinders

Components

Fixed dust curtains – four sides

Benefits & Features

Mandatory Attachments – POWER TRAIN

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mandatory Attachments – MAST

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Mandatory Attachments – UNDERCARRIAGE

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Mandatory Attachments – OPERATOR ENVIRONMENT

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Control Group

Standard (includes all parts listed under standard equipment)
Deluxe (includes standard machine control group features) plus: – Auto leveling and retract – Automation/operator assist auto angle
Ultra (includes deluxe control group features) plus: – Auto drilling, excluding pipe change – One-touch drilling is only applicable when using single pass drilling

Mandatory Attachments – SERVICE STATION

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Control Group

Standard (includes all parts listed under standard equipment)
Deluxe (includes standard machine control group features) plus: – Auto leveling and retract – Automation/operator assist auto angle
Ultra (includes deluxe control group features) plus: – Auto drilling, excluding pipe change – One-touch drilling is only applicable when using single pass drilling

Fast fill, full service, rotary: – Full service center, fill and evacuation fuel, compressor, coolant, engine oil, hydraulic and gear box – 500 hours engine oil reserve system

Mandatory Attachments – COOLING

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Control Group

Standard (includes all parts listed under standard equipment)
Deluxe (includes standard machine control group features) plus: – Auto leveling and retract – Automation/operator assist auto angle
Ultra (includes deluxe control group features) plus: – Auto drilling, excluding pipe change – One-touch drilling is only applicable when using single pass drilling

Fast fill, full service, rotary: – Full service center, fill and evacuation fuel, compressor, coolant, engine oil, hydraulic and gear box – 500 hours engine oil reserve system

Climate, standard climate range: – Ambient temperature range: –1° C (30° F) to 48° C (118° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass
Hot climate: – Ambient temperature range: –1° C (30° F) to 52° C (125° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass – Window shades – High temp hydraulic oil – High temp compressor oil

Mandatory Attachments – DUST SUPPRESSION

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Control Group

Standard (includes all parts listed under standard equipment)
Deluxe (includes standard machine control group features) plus: – Auto leveling and retract – Automation/operator assist auto angle
Ultra (includes deluxe control group features) plus: – Auto drilling, excluding pipe change – One-touch drilling is only applicable when using single pass drilling

Fast fill, full service, rotary: – Full service center, fill and evacuation fuel, compressor, coolant, engine oil, hydraulic and gear box – 500 hours engine oil reserve system

Climate, standard climate range: – Ambient temperature range: –1° C (30° F) to 48° C (118° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass
Hot climate: – Ambient temperature range: –1° C (30° F) to 52° C (125° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass – Window shades – High temp hydraulic oil – High temp compressor oil

Water injection, 2324 L (614 gal): – One (1) tank with 1378 L (364 gal) – Two (2) tanks with 473 L (125 gal) each – Fast fill water system – Stainless steel plumbing – ECM control of water injection pump interlock – Water flow meter/current control and tank level

Mandatory Attachments – STAIRS

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Control Group

Standard (includes all parts listed under standard equipment)
Deluxe (includes standard machine control group features) plus: – Auto leveling and retract – Automation/operator assist auto angle
Ultra (includes deluxe control group features) plus: – Auto drilling, excluding pipe change – One-touch drilling is only applicable when using single pass drilling

Fast fill, full service, rotary: – Full service center, fill and evacuation fuel, compressor, coolant, engine oil, hydraulic and gear box – 500 hours engine oil reserve system

Climate, standard climate range: – Ambient temperature range: –1° C (30° F) to 48° C (118° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass
Hot climate: – Ambient temperature range: –1° C (30° F) to 52° C (125° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass – Window shades – High temp hydraulic oil – High temp compressor oil

Water injection, 2324 L (614 gal): – One (1) tank with 1378 L (364 gal) – Two (2) tanks with 473 L (125 gal) each – Fast fill water system – Stainless steel plumbing – ECM control of water injection pump interlock – Water flow meter/current control and tank level

Frame, Standard: – Includes basic mainframe and deck features plus: - Fixed stairs to main deck cab area, on cab side of frame
Frame, Ultra: – Includes basic mainframe and deck features plus: - Cascading, self-leveling stairs to main deck cab area - Stairs on cab side of the frame - Switched walkway lighting at ground and deck levels - Tram interlock if stairs are down

Optional Attachments

Optional attachments may vary. Consult your Cat dealer for details.

Engine and Compressor

Low horsepower package: – Engine: Tier 2 equivalent, 680 kW (912 hp), 1,800 rpm – Compressor: 56.6 m3/min (2,000 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, poppit inlet – Fixed displacement
High horsepower package: – Engine: Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 42.5 m3/min (1,500 ft3/min) @ 10.3/24.1/34.5 bar (150/350/500 psi), 1,800 rpm, poppit inlet – Hi/low pressure switch, bit oil injection system, 114 L (30 gal) for DTH – Fixed displacement
High horsepower package: – Engine, Tier 2 equivalent, 775 kW (1,039 hp), 1,800 rpm – Compressor: 73.6 m3/min (2,600 ft3/min) @ 6.9 bar (100 psi), 1,800 rpm, butterfly inlet – Adjustable from half to full displacement

Mast, Pipe Carousel, 10 m

10 meter mast, five (5) pipe carousel
Mast: – Up to 10.29 m (33 ft 9 in) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 10.67 m (35 ft) length drill pipe – With bit sub 76 cm (30 in)
Carousel: – Five (5) pipe capacity allowing 63.39 m (208 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 10.67 m (35 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 346 kg (91,152 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 13 m

13 meter mast, five (5) pipe carousel with additional mast rest
Mast: – Up to 13.4 m (44 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using one (1) each 12.19 m (40 ft) length drill pipe with bit sub 229 cm (90 in)
Carousel: – Five (5) pipe capacity allowing 74.37 m (244 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 12.19 m (40 ft) length drill pipe (drill pipe not included) – Bit load with one pipe up to 41 563 kg (91,630 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Mast, Pipe Carousel, 16 m

16 meter mast, four (4) pipe carousel with additional mast rest
Upper roller pipe catcher arm with drill function interlock when pipe catcher is not closed
Mast: – Up to 16.46 m (54 ft) single pass hole depth – Drill on tracks, changing bit above deck – Single pass hole using two (2) each 7.62 m (25 ft) length drill pipe – With bit sub 228.6 cm (90 in)
Carousel: – Four (4) pipe capacity allowing 46.93 m (154 ft) total hole depth – Pipe diameter 194 mm (75⁄8 in) or 219 mm (85⁄8 in) – 7.62 m (25 ft) length drill pipe (drill pipe not included) – Bit load with two pipes up to 42 000 kg (92,594 lb) – Winch 3629 kg (8,000 lb) with 1588 kg (3,500 lb) lift capacity

Rotary Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 76.2 cm (30 in) long – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Roller bushing – Bit sub 228.6 cm (90 in) – Four (4) pipe retainer

DTH Application

Mast, 10 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 13 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Five (5) pipe retainer
Mast, 16 m – diameter, 194 mm (75⁄8 in) or 219 mm (85⁄8 in): – Tooling 194 mm (75⁄8 in) or 219 mm (85⁄8 in) diameter – Split bushing – Customer supplied bit sub – Four (4) pipe retainer

Top Sub/Shock Sub

Top sub, rotary application: – Standard for rotary application, DTH cannot use top sub
Shock sub, dual application: – DTH has to use shock sub, optional for rotary application – Shock sub with crossover sub, rotary or DTH

Deck Wrench

Sliding deck wrench with standard bit basket
Sliding deck wrench with hydraulically operated bit basket

Drill Pipe Catcher

Pipe catcher, fixed cable
Pipe catcher, hydraulic drill function interlock

Undercarriage, 750 mm (29.53 in): – Undercarriage with full length rock guards and tram distance meter – 750 mm (29.53 in) triple grousers – Used for soft ground application
Undercarriage, 600 mm (23.62 in): – Undercarriage with full length rock guards and tram distance meter – 600 mm (23.62 in) triple grousers – Used for hard ground application

Control Group

Standard (includes all parts listed under standard equipment)
Deluxe (includes standard machine control group features) plus: – Auto leveling and retract – Automation/operator assist auto angle
Ultra (includes deluxe control group features) plus: – Auto drilling, excluding pipe change – One-touch drilling is only applicable when using single pass drilling

Fast fill, full service, rotary: – Full service center, fill and evacuation fuel, compressor, coolant, engine oil, hydraulic and gear box – 500 hours engine oil reserve system

Climate, standard climate range: – Ambient temperature range: –1° C (30° F) to 48° C (118° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass
Hot climate: – Ambient temperature range: –1° C (30° F) to 52° C (125° F) – Cab cooling to 19° C (66° F) – Safety laminated tinted glass – Window shades – High temp hydraulic oil – High temp compressor oil

Water injection, 2324 L (614 gal): – One (1) tank with 1378 L (364 gal) – Two (2) tanks with 473 L (125 gal) each – Fast fill water system – Stainless steel plumbing – ECM control of water injection pump interlock – Water flow meter/current control and tank level

Frame, Standard: – Includes basic mainframe and deck features plus: - Fixed stairs to main deck cab area, on cab side of frame
Frame, Ultra: – Includes basic mainframe and deck features plus: - Cascading, self-leveling stairs to main deck cab area - Stairs on cab side of the frame - Switched walkway lighting at ground and deck levels - Tram interlock if stairs are down

MAST ACCESS LADDER

Ladder to access mast, grating for maintenance inside mast
Posts only for lanyard attachment to use with cable for traveling hook and harness

OPERATOR ENVIRONMENT

Window Shades: – Included in hot climate package – Optional for other climate packages

ATTACHMENTS

Dust suppression
Hydraulic dust curtains: – Fixed curtains on left and right sides – Auto raise hydraulic lifted curtains for rear and front – Includes ECM control tram interlock if dust curtains are not up
Drill pipe: – Drill pipe, 194 mm × 7.62 m (75⁄8 in × 25 ft): - 194 mm (75⁄8 in) diameter, 7.62 m (25 ft) long, 152 mm (6 in) BECO threads - For use with 16 m mast – Drill pipe, 194 mm × 7.62 m (75⁄8 in × 25 ft): - 219 mm (85⁄8 in) diameter, 7.62 m (25 ft) long, 152 mm (6 in) BECO threads - For use with 16 m mast – Drill pipe, 194 mm × 9.14 m (75⁄8 in × 30 ft): - 194 mm (75⁄8 in) diameter, 9.14 m (30 ft) long, 152 mm (6 in) BECO threads - Recommended for 13 m mast DTH starter steel – Drill pipe, 194 mm × 9.14 m (75⁄8 in × 30 ft): - 219 mm (85⁄8 in) diameter, 9.14 m (30 ft) long, 152 mm (6 in) BECO threads - Recommended for 13 m mast DTH starter steel – Drill pipe, 194 mm × 10.67 m (75⁄8 in × 35 ft): - 194 mm (75⁄8 in) diameter, 10.67 m (35 ft) long, 152 mm (6 in) BECO threads - For use with 10 m mast – Drill pipe, 194 mm × 10.67 m (75⁄8 in × 35 ft): - 219 mm (85⁄8 in) diameter, 10.67 m (35 ft) long, 152 mm (6 in) BECO threads - For use with 10 m mast – Drill pipe, 194 mm × 12.19 m (75⁄8 in × 40 ft): - 194 mm (75⁄8 in) diameter, 12.19 m (40 ft) long, 152 mm (6 in) BECO threads - For use with 13 m mast – Drill pipe, 194 mm × 12.19 m (75⁄8 in × 40 ft): - 219 mm (85⁄8 in) diameter, 12.19 m (40 ft) long, 152 mm (6 in) BECO threads - For use with 13 m mast
Clean: – Blow down hose with nozzle: - Clean with air
Dust control: – Spray water on dirt when tramming starts – For use with water injection
Winch control: – Winch control, remote: - Remote pendant winch control
Platform: – Tank platform, fire suppression: - Holds up to three (3) of 113 kg (250 lb) tanks
JIB crane: – JIB crane, pedestal control: - Mounted on drill deck – JIB crane, remote control: - Radio remote control
Start up commissioning: – Factory service engineer on site for 12 working days to direct start-up and commissioning, and provide hands-on maintenance and operation training

Equipment

Standard equipment

POWER TRAIN

Engine, Cat C32 ACERT, Tier 2/Stage II equivalent, 1,800 rpm

Manifold covers, turbo and exhaust

Engine fire frame

Fire wall, engine and hydraulic drive

Exhaust pipe blankets

MAST

Hole diameter, up to 311 mm (121⁄4 in)

Rated capacity, up to 383 kN (86,000 lbf)

Pulldown/hoist system, single cylinder

Rotary drive, dual motors

0-137 rpm, 0-17 313 N·m (0-12,769 lbf-ft) maximum torque

Angle drilling, up to 30 degrees

Mast locks and indicator in cab

Auto cable tensioning system

Hydraulic Operated Break-Out wrench (HOBO)

Shear bolt deck wrench cover

Dust hood with hinged quick change dust seal

Remote thread lube system

Mast lanyard mounting plates

OPERATOR ENVIRONMENT

Cab, shock mounted, insulated

Two-man extra-large FOPS

Cat operator seat with air suspension

Trainer’s seat

Operator’s console: split with stainless steel panels

Electric controls for drilling, tramming, leveling and auxiliary functions

Dome lights, overhead interior

Dash light

Two (2) hinged doors, heavy duty latching

Twelve (12) windows

Full front drill window

Roof window with protective cage

Windshield wipers, washer tank kit

Air conditioning/heating/pressurizing roof mounted, hydraulic driven

Cab ladder, roof platform and railing

Electric horn

Slope indicators

CD stereo kit with speakers

24V to 12V converter

English control system display text may be changed to other languages

Electronic Control Module (ECM)

HMI touch screen control

Drill performance monitoring and diagnostics system

Drill depth meter

Travel stop, virtual rotary head

Jack/tram interlock

Tram interlock, pipe in hole

Tram interlock: mast up and locked or down and parked

Mast lock indicator

Tram speed select interlock: high only when mast is down

Tram interlock: machine outside stability limits

Drill function interlock mast up and locked

Head clear interlock: rotary drive clear of carousel

Winch interlock

Pipe positioner sensor

Jack pressure sensor

Rotary head RPM gauge, digital

Rotary torque control

Electronic compressor control

Filter indicators

Pump drive gearbox temperature sensor

Basic engine shut down timer

Cab environment control: AC, filter indicator, heat, fan speeds

Wiring for terrain interface

SAFETY AND SECURITY

Air hose safety sleeves (whip socks)

Hinged protective cage: for drill view window

Battery and starter disconnects with lock-outs

Eight (8) engine shut down buttons

Tram alarm

Strobe beacon on: – Cab and front left side of drill – Clearance light, mast crown

Twenty (20) lights for night drilling

Two (2) closed circuit cameras (front and left side) with monitor in cab

COOLING

Shutdown switch, low coolant level

Cooler fans, variable speed, ECM

FRAMES

Four (4) leveling jacks: – Two (2) × 121.9 cm (48 in) rear – Two (2) × 152.4 cm (60 in) front

Tow hooks, front end

Lift lugs, for base machine without mast

Mast raise cylinders, two stage

Walkways, around the drill, 360 degrees

Decks and walkways, slip resistant

Hand rails, bolt-on with kick plates

Swing up steps, access/egress

Self-closing gates

Stationary, rear deck

Hydraulic viewing hatch with LED hatch viewing spot light

Fixed dust curtains, four sides

Rear deck bit storage box with aluminum cover

Pipe loading guide roller

Left rear swing gated handrail, dual gate

Fuel tanks: – Two (2) tanks mounted below deck – 3217 L (850 gal) fuel – Manual and remote fill – Isolation valves

Hydraulic tank with isolation valves and interlocks

Cat maintenance free batteries

Battery box, stainless, sliding drawer

Cat remote jump start terminals

OTHER STANDARD EQUIPMENT

Standard Caterpillar colors

Foam injection connection

Loop filters between hydraulic pumps and motors

Return filters, hydraulic

Auto lubrication system, centralized

Feed traveling sheave lube provision

Hydraulic pressure test points

You are here

Vertical Tabs

OVERVIEW

Standard equipment

Follow us